Opel Corsa forum - club

klari píše:Piekny profi projekt!!!
Szacunek-Respect! I'm impressed!!!

Thanx

klari píše:You're fit the poli bushes - it's the suspension ,or driving much harder or tough!? I heard that if I fit this poli stuff that the car-body can hurts becuse they are so hard!!!? It's that true!?

There are some different fabricants.
Friends made them for sprints from nylon, very hard, for 1/4 mile races good, but not for road use.

I have Polyurethan, but they are not all the same, some are harder.

Mine are from Powerflex, and they are not super hard. They are good for extreme road use!
I did not notice the difference very much, because I mounted the KW variant 3 coilovers at the same moment, so the Corsa was totally different.
But with 2 liter engine, I would say, put them on!!! Much better then original!

klari píše:Have you some photos of build rear disc's brakes???
I got complete new parts from Vectra A GT (rear disc brakes) and i have to fit it into my corsa. I've You have some photos or some helps than please share I will be thankfull!!!

I have drawing and .dxf-file from the metal that you must weld to the Corsa axis. I am going to mount Zafira brakes, these have handbrake in the caliper. Vectra GT has handbrake in the disc. But is not very different.

Maybe this can be helpfull: http://oege.ie.hva.nl/~jelsma02/discconversion.pdf

If you have any questions, just ask

Thanks,!!!!if have also some questions that just ask!!
Ok i have go to work!!:/

Trosku aktualisace...

Kola na sprinty: 15" a 8.5J


Nova kliku:




V bloku:


Pisty. Nove od JE: http://www.jepistons.com/


Upraveni pro ventily:


A spodek skoro hotove:


Hlava:


A s Anglie Jenvey Throttle Body's: http://www.jenvey.co.uk/
Zaroven me prislo DTA, stavitelnou ECU. http://www.dtafast.co.uk/

Nikomu nic nerikejte ale!

Tohle bude prekvapko na spinty

Fakt blázen

Eriku, ty jsi vážně šílený.

Tak fakt klobouk dolu, Eriku rekni ake je tve povolani jakou mas profesy? Ty jsi fakt borec, no jinka ty kola na sprinty toje pecka

Studuju technickou visokou. Odbor automobilku...

Jinak makam na brigade jak blbec, ale to se musis umet vyridit dobrou haha
Jinak moc kseftuju s dylama...

Prave jsem zbiral dily na nove motor asi uz 2 roky, tech dilu jsem tedka prodaval, a toho je hodne haha, 1 motor komplet, 1 dalsi motor, atd atd, + to co by me to stalo, zpravit ten co se mi tedka rozbilo, skoro vijde na stejno, postavit neco uplne sileneho

Eriku,...
!
!
!

Dnes jsem prodal jeden 2 liter co jsem mel doma, a dve prevodovky.
Zitra sperra a ostre vacky, chip atd...

A budeme mit zase penecky na zbytek projectu

Erik vydelava jen na auto

ale jinak mooooc pekny

Erik: you have c20xe!?

In this photo:

is a shaft with wheel (witch is marked on red) with 4 holes... !?
Original wheel from c20xe is diffrent and got 6 holes and the screw for thight this together is on torx key.
Did you have shaft from x20xev!?? couse this is strange..

One thing that I can say is:
GO GO GO!!
Good work!!!

hh no mazec uplně, tomu říkám ,,zapálený automechanik" =D krásný prostě

Dub.- píše:hh no mazec uplně, tomu říkám ,,zapálený automechanik" =D krásný prostě

To není zapálený automechanik. To je prostě Erik

tak jako vážně smekám. Corsička je úžasná a motorově nemluvě, to jen tiše závidím..fakt jsi šikovnej